Abstract
Flow simulation is important in planning and design of engineering hydraulic structures. The purpose of this study is to predict flow in the Lutanandwa river catchment in the Luvuvhu river basin, Limpopo, South Africa. The input data needed for SWAT model set up included Digital Elevation Model (DEM), hydro meteorological data, land cover and soils data acquired from various institutions in South Africa. The DEM was processed from contours in the Department of Hydrology and Water Resources, University of Venda. Meteorological data was acquired from the South African Weather Service (SAWS). Observed daily stream flow data was obtained from the Department of Water Affairs and Sanitation. Land cover data was acquired from processed satellite imagery obtained from the department of Environmental Affairs and ground truthing carried out to verify the land cover information. Soils information was obtained from the Agricultural Research Council – Institute of Soil, Climate, and Water (ARC-ISCW). The soils data was obtained in the form of geo referenced land type map. Based on assessment of the data status, the period 2002 to 2014 was selected for modeling. The meteorological data processed for this period was prepared in the appropriate format for model set up. Soil water characteristic calculator was used to estimate the soil properties required as input to SWAT model. The land cover types in the study area was converted to corresponding SWAT land use types. The statistical parameters required as input to the weather generator in the SWAT model was calculated using the pcpSTAT programme which was used to compute the parameters using weather information. All input data was processed and prepared in the appropriate format for model set up. The processed input data was loaded into the Geographic Information Systems (GIS) interface of the SWAT model to enable model set up for flow simulation.
References
Aklonis, J.J and W.J MacKnight. 1983. Introduction to Polymer Viscoelasticity. 2nd Ed. John Wiley and Sons, New York.
Balevičiu, R., I. Sielamowicz, Z. Mróz and Kačianauskas, R. 2011. Investigation of wall stress and outflow in a flat-bottomed bin: a comparison of the DEM model results with the experimental measurements. Powder Technology, 214, 322–336. doi: 10.1016/j.powtec.2011.08.042.
Briassou, D., and Curtis, J. 1985. "Design and Analysis of Silos for Friction Forces," Journal of Structural Engineering, 3 (6), June 1985, 1377-1398.
Chattopadhyay, A., R.K. Rao and M.A. Parameswaran. 1994. On the classification of bulk solids. Bulk Solids Handling, 14,339-344.
Chen, W.R and G.Y. Baladi. 1985. Soil Plasticity. New York: Elsevier.
Chi, L and Kushwaha, R.L. 1990. Lade’s elastoplastic model for granular soils. American Society of Agricultural Engineers. Paper No. 90-1084.
Cundall, P.A., and O.D. Strack. 1979. A discrete element model for granular assemblies. Géotechnique, 29, 47–65.
Chung, T.J. 1988. Continuum Mechanics. Prentice-Hall International, Inc.
Dartevelle, S. 2003. Numerical and granulometric approaches to geophysical granular flows, Ph.D. thesis, Michigan Technological University, Department of Geological and Mining Engineering, Houghton, Michigan.
Eurocode, L. 2003. Actions on structures. Part 4: Actions in silos and tanks. Ref. No. EN 1991-4.
Oranga, E. 2005. Elastic and Viscoelastic Behaviour of Shelled Maize En Masse. Master’s thesis. University of Nairobi, Kenya.
Findley, W.N., J.S. Lai and K. Onaran. 1976. Creep and Relaxation of Non- Linear Viscoelastic Materials. Vol. 18 North-Holland Publishing Co., Amsterdam.
González-Montellano, C., E. Gallego, Á. Ramírez-Gómez and F. Ayuga. 2012. Three dimensional discrete element models for simulating the filling and emptying of silos: Analysis of numerical results. Computers and Chemical Engineering, 40, 22–32. doi: 10.1016/j.compchemeng.2012.02.007.
Gumbe, L.O. 1995. Load deformation behaviour of soils and en-masse grains. Paper Presented at the Symposium on Unsaturated Soil Behaviour and Applications. Nairobi, Kenya
Gumbe, L.O. 1993. A Discussion on Constitutive Equation for Granular Materials En-masse. East African Journal of Engineering. 1(1): 27 – 38.
Gumbe, L.O. 1990. Material Characterisation and Prediction Equations for Loads in Silos Containing Granular Materials En-masse. African Journal of Science and Technology, Series A: 8(1): 1 - 5.
Gumbe, L.O. and B.M. Maina. 1990. Elastoplastic Constitutive Parameters for Rice En-masse. African Journal of Science and Technology, Series A: 8(2): 15 - 25.
Harri, D. 2009. An elastoplastic model for deformation and flow of granular materials and its connection with micro mechanical quantities. In: Powders and Grains 2002:
Proceedings of the 6th international conference on micromechanics of granular media. 1145, 1085-1088. doi: 10.1063/1.3179833
Heinrich, M.J., R.N Sidney and P.B Robert. 1996. The Physics of Granular Materials. In: Physics Today, pp 32
Herum, F.L., et al., 1979. "Viscoelastic Behavior of Soybeans Due to Temperature and Moisture Content," Transactions of ASAE, 22, (5), 1220-1224.
Horabik, J. and M. Molenda. 2014. Mechanical Properties of Granular Materials and Their Impact on Load Distribution in Silo: A Review. Scientia Agriculturae Bohemica. 45(4): 203–211
Ishihara, K. and S. Okada. 1978. Effects of stress history on cyclic behavior of sand. Soils and Foundation 18(4): 31-45.
ISO 3535. 1977. Continuous mechanical handling equipment – Classification and symbolization of bulk materials. International Agrophysics, 14,385-392
Janssen, H.A. 1895. Experiments on grain pressure in silos. Verein Deutscher Ingenieure, Zetschrift (Düsseldorf), 39, 1045–1049. (in German).
Jenike, A.W. 1961. Gravity flow of bulk solids. Bulletin of the University of Utah, 52, 1-309.
Kobyłka, R. and M. Molenda. 2014. DEM simulations of loads on obstruction attached to the wall of a model grain silo and of flow disturbance around the obstruction. Powder Technology, 256, 210–216. doi:10.1016/j.powtec.2014.02.030.
Kobyłka, R. and M. Molenda. 2013. DEM modelling of silo load asymmetry due to eccentric filling and discharge. Powder Technology, 233, 65–71. doi: 10.1016/j.powtec.2012.08.039.
Kou, H.P., P.C. Knight, D.J. Parker, Y. Tsuji, M.J. Adams and J.P.K. Seville. 2002. The influence of DEM simulation parameters on the particle behaviour in a V-mixer. Chemical Engineering Science, 57, 3621–3638.
Lade, P.V. 1977. Elasto-plastic stress- strain theory for cohesionless soil with curved yield surface. International Journal of Solids and Structure; 13: 1019-1035.
Lade, P.V. 1972. The stress-strain and strength characteristics of cohesionless soils. Ph.D. thesis. University of Califomia, Berkeley.
Lade, P.V. and J.M. Duncan. 1971. Stress-path dependent behavior of cohesionless soil. ASCE J. of Geotechnical Engineering Division 102(GT1): 51-68.
Lee, K.L. and F. Albaisa. 1974. Earthquake induced settlements in saturated sands. ASCE J. of Geotechnical Engineering Division 100(GT4): 387- 406.
Li, Y., Q. Zhang, V.M Puri and H.B Manbeck. 1989. Elasto-plastic constitutive equation parameters and load response of wheat en-masse-part-I, initial density, moisture content and strain rate effects. Trans. of ASAE 32(1): 194-202
Manbeck, H.B., and Nelson, G.L. 1975. Three Dimensional Constitutive Equations for Wheat En Masse. Transactions of ASAE, 18 (6)1122-1127.
Manbeck, H.B., and Nelson, G.L. 1972. Methods and Instrumentation for Evaluating the Stres-Strain Behavior of Wheat En Masse. Transactions of ASAE, 919-922, American Society of Agricultural Engineers, St. Joseph, Michigan.
Masson, S. and J. Martinez. 2000. Effect of particle mechanical properties on silo flow and stress from distinct element simulations. Powder Technology, 109, 164–178. doi: 10.1016/ S0032-5910(99)00234-X.
Mensah, J.K., et al., 1981. Effect of Drying Conditions on Impact Shear Resistance of Selected Corn Varieties. Transactions of ASAE. 24(6), 1568-1572, American Society of Agricultural Engineers, St. Joseph, Michigan.
Mohsenin, N.N. 1980. Thermal Properties of Foods and Agricultural Materials. Gordon and Breach, New York
Moya, M., F. Ayuga, M. Guaita and P.J Aguado. 2002. Mechanical properties of granular agricultural materials considered in silos design. ASCE Engineering Mechanics Conference; Colombia University, New York
McLaughlin, N.B. and R.E. Pitt. 1984. Failure characteristics of apple tissue under cyclic loading. Trans. of ASAE 27: SE 1984: 311-320
Oda, M., I. Koishikawa and T. Higiuchi. 1978. Experimental study of anisotropic shear strength of sand by plane strain test. Soils and Foundations 18(1): 26-38.
Ozdemir, H. 1976. Nonlinear transient dynamic analysis of yielding structures. Ph.D. thesis. University of California, Berkeley.
Parafiniuk, P., M. Molenda and J. Horabik. 2013. Discharge of rapeseeds from a model silo: physical testing and Distinct Element Method simulation. Computers and Electronics in Agriculture, 97, 40–46.
Peleg, M. 1985. The role of water in rheology of hygroscopic food powders. In: Simataos D, Multon JL (eds): Properties of water in foods. Martinus Nijhoff Publishers, Dordrecht, 394-404.
Stafford, J.V., E. Audsley and Sharp, J.R. 1986. The determination of best fit linear failure envelopes to Mohr Circles. J. Agric Eng. Res. (1986)33, 33-38.
Shelef, L. and N. N. Mohsenin. 1968. Effects of Moisture Content on Mechanical Properties of Corn horny Endosperm. Cereal chemistry 46 (3): 242-253.
Stinchcomb, W.W. 1989. Damage and fracture of composite materials under cyclic loads. Advances in fracture research. Salama, Ravi-Chandar, Taplin and Rama (eds); 4: 2939-2955
Schott, R.W., and Britton, M.G. 1984. Plane Strain Behavior of Bulk Grain. ASAE Paper No. 84-503, American Society of Agricultural Engineers, St. Joseph, Michigan.
Sykut, J., M. Molenda and J. Horabik. 2008. Influence of filling method on packing structure in model silo and DEM simulations. Granular Matter, 10, 273–278.
Ti, K.S. 2009. A review of basic soil constitutive models for geotechnical application. EJGE Vol. 14, Bund. J
Tordesillas, A. 2004. The jekyl and hyde of granular materials uncovered. www.unimelb.edu.au/
Vanel, L., P. Claudin, P.J. Bouchaud, M.E Cates, E. Clement and J.P Witterner. 2000. Comparison between theoretical models and new experiments. Physical Review Letters; 84(7): 1439-1442.
Youngs, R.R. 1982. A three-dimensional effective stress model for cyclicly loaded granular soils. Ph.D. diss. The University of California, Berkeley.
Zhang, Q., V.M Puri, H.B. Manbeck. 1994. Applicability of a two-parameter failure criterion to wheat en masse. Trans. of ASAE. 37(2): 571-575.
Zhang, Q., M.G. Britton and R. Jaremek. 1993. Dynamic loads during discharge for wheat, barley and canola in a smooth and a corrugated-walled model bin. Journal of Agricultural Engineering Research, 56, 111–119. doi: 10.1006/jaer.1993.1065
Zhang, Q., V.M, Puri and H.B. Manbeck. 1986. Determination of Elasto-plastic Constitutive Parameters for Wheat En Masse. ASAE Paper No. 86-4073, American Society of Agricultural Engineers, St. Joseph, Michigan.
Zhang, Q., V.M. Puri and H.B. Manbeck. 1985. Finite Element Modelling of Thermally Induced pressures in Grain Bins Filled with Cohensionless Granular Material. ASAE Paper No. 85-4002, American Society of Agricultural Engineers, St. Joseph, Michigan.
Kasap, S.O., S. Yannacopoulos, V. Mirchandani and J.R. Hildebrandt. 1992. Ultrasonic Evaluation of Thermal Fatigue of Composites. Journal of Kumar.
Magurno, A. 1999. Vegetable fibres in automotive interior components. Die Angew Makromol Chem. 272, 99–107.
Maxwell, A.S., W.R Broughton, G. Dean and G.D Sims. 2005. Review of accelerated ageing methods and lifetime prediction techniques for polymeric materials. Engineering and Process Control Division, HMSO and Queen’s Printer, NPL Report DEPC MPR 016 ISSN 1744-0270, Scotland.
Perrot, Y., C. Baley, Y. Grohens and P. Davies. 2007. Damage Resistance of Composites Based on Glass Fibre Reinforced Low Styrene Emission Resins for Marine Applications. Applied Composite Materials.14(1) 67-87.
Rapra.2012. http://www.rapra.net/composites/material-selection/some-design-considerations.asp. Retrieved from http://www..net. On 24/02/2016
Wang, Y., S. Lim, J.L Luo and Z.H. Xu. 2006. Tribological and Corrosion Behaviors of Al2O3/Polymer Nanocomposite Coatings. Wear. 260(9-10): 976-983.
This work is licensed under a Creative Commons Attribution 4.0 International License.